This just tells me calipers should have 2 measuring bars on them, so gaps and other inside edges can be measured like this (maybe this already exists, idak)
That’s what the two prongs at the top are for. Flip the caliper upside down, use the prongs to measure the inside dimension, and read it off the same scale.
I think the guy was actually referring to something a bit different, that is having a second number scale on the caliper that is offset by the width of the first jaw, so you can use the outside jaws for measuring inside dimensions. I don’t think that would work, however.
The second scale sounds like a good Idea till you mess up everything due to using the wrong one. I once had a Spirit Level that was for plumbers and had a Second bubble-level built in that was even when the Level was tiltet to about 1.5 degree, great for waste-lines and gutters. Now everything in my House ist tilted by 1.5 degree except the plumbing and gutters.
I was indeed (and I think you’re right, the calipers would need at least to be parallel on their outer edges to work this way).
I’m not sure what rz2000 was doing by (slightly wrongly) rewording basically what I wrote — I get the impression they think I was being full of myself for thinking of a (similar) concept that already exists (despite conceding that it already might) and felt the need to put me back in place.
By using the same scale for inside and outside, you can take one measurement inside, and compare it to something else as outside without moving the scale at all.
Can’t tell if I’m missing a joke here, but see those two small knife looking protruding from the opposite side (above) where they’re measuring, those are used for measuring internal diameter.
The side they’re using is for outer diameter.
And though you can’t see it in the pic, the thin bit of metal that extends out from the bottom can be used for measuring depth.
This just tells me calipers should have 2 measuring bars on them, so gaps and other inside edges can be measured like this (maybe this already exists, idak)
Just flip it, the top bars are for measuring from the inside.
That’s what the two prongs at the top are for. Flip the caliper upside down, use the prongs to measure the inside dimension, and read it off the same scale.
Ah cool, didn’t notice those. Cheers
“Caliper jaws for inside measurement—I thought of that. Turned out it already existed, but I arrived at it independently."
I think the guy was actually referring to something a bit different, that is having a second number scale on the caliper that is offset by the width of the first jaw, so you can use the outside jaws for measuring inside dimensions. I don’t think that would work, however.
The second scale sounds like a good Idea till you mess up everything due to using the wrong one. I once had a Spirit Level that was for plumbers and had a Second bubble-level built in that was even when the Level was tiltet to about 1.5 degree, great for waste-lines and gutters. Now everything in my House ist tilted by 1.5 degree except the plumbing and gutters.
I was indeed (and I think you’re right, the calipers would need at least to be parallel on their outer edges to work this way).
I’m not sure what rz2000 was doing by (slightly wrongly) rewording basically what I wrote — I get the impression they think I was being full of myself for thinking of a (similar) concept that already exists (despite conceding that it already might) and felt the need to put me back in place.
By using the same scale for inside and outside, you can take one measurement inside, and compare it to something else as outside without moving the scale at all.
Can’t tell if I’m missing a joke here, but see those two small knife looking protruding from the opposite side (above) where they’re measuring, those are used for measuring internal diameter.
The side they’re using is for outer diameter.
And though you can’t see it in the pic, the thin bit of metal that extends out from the bottom can be used for measuring depth.
TIL what the thin bit is for. Thanks
Probably not because I would have said the same thing. I know nothing about tools.
Same thought, Im not sure if that comment is a joke or not…